GoPro Grab Bag for HERO Cameras (Official GoPro Accessory)

Purchased to replace an old one that broke in the freezing temperature always a good quality product

Where you can, buy the proper attachments as they tighten better and grip far easier than dupes. This set was perfect for what we needed it for plus the rubber compression part stopped any vibration affecting any recording! Easier to slide than the dupes plus look and feel better quality. ⭐️⭐️⭐️⭐️⭐️

Nice variety of items in there without too much of a cost. Some did break after a few months but most were ok

Amazing quality product with great delivery time. Everything was genuine and fitted like a glove, very much worth the cost. Easy to fit and use and very long lasting adhesive. I would HIGHLY recommend this product and seller over many others.

The usual great GoPro product.

How is that? The most common mount on their cameras is, the buckle mount. Can you buy it singularly?? No. Are there alternatives? Yes, loads. But I’ve had as much as 3mm play on the ’others’ They are cheap copies, not totally compatible and produce wobbly shots. A case of get what you pay for? I think GoPro are ok with this because they can sell you their premium grab bags of parts, that you will only use about 25% of and, you don’t get a bag! It’s just very clever marketing. Have to say, the buckles are great quality and lock together solid. They are just not copied in any great detail so any copies I’ve had, now I’ve started to use this mount more, are just no good.

I work with gopros, Sony FDR's everyday now, and I hate ( HATE ) the " cheap " versions of gopro mounts, their always loose fitting when it comes to the curve or flat mount, (causing camera shake) my local stores have stopped stocking the " grab bags " from gopro. very happy with this order, legit gopro parts, yes they are more expensive, but with you want to secure your £500 + camera use these!.

A nice selection of pieces to fine-tune your setup. Was cheaper than directly from GoPro too due to their postage costs.

Son muy buenos adaptadores que si resisten los golpes, por eso me gustan los originales.

This is a nice little set of various pieces and spare parts that is handy to keep around when you’re trying to build that perfect GoPro mount. The set includes a curved mounting base with 3M VHB tape, a flat mounting base with 3M VHB tape, a standard height mount, an extended height mount, a pivot arm that consists of two pieces, two small thumbscrews, a standard length thumbscrew, and a shorter thumbscrew. If you combine the curved mounting base, the standard height mount, and the normal thumbscrew you have a duplicate of what usually comes with a GoPro camera. Then you’re left with the flat mounting base, the higher mount, and the pivot arm. Combining those parts gives you a nice raised arm that can pivot both back and forth and side to side so you can get a level shot even if you need to mount the base at an angle. The set includes a shorter thumbscrew that can be used when you don’t want the thumbscrew to extend beyond the edge of the camera. This is useful if you are tilting the camera at a 90 degree side angle as it allows a full tilt without the thumbscrew impacting the main part of the mount. The only downside is that the tolerance is very tight and it will be hard to fully tighten the thumbscrew so you may need to use a screwdriver to tighten it down if you need it to be completely locked in place. I mainly got this set in order to get the extended height mount and the pivoting arm. Combining these two things will raise your GoPro about 3 inches off the mounting surface and provide a different perspective versus the standard low mount. I’m using a GoPro mount in my car and the standard mount results in video that doesn’t give a good view of what’s directly in front of the car. Using this kit allows me to raise the camera up higher and angle it down a bit to get more of the ground in front of the car in the frame. All of the pieces seem very sturdy. I’d much rather pay a little more for the genuine GoPro accessories versus having a cheap knockoff fail at a bad time. Highly recommended set if you’d like to add some versatility to your setup!

A perfect grab option to enhance the gopro extensions 2 long screw 2 small.screw..3 joint extensions to support while.on helmet or on suction cup 2 additional adhesives for users comfort and backup if one cracks you have the option to replace Best in price ....durable

Did not include parts for the gopro 3-Way. The picture indicate the parts looks like thumb screw for the gopro 3-way but they are not the same. Wasted.

Le GoPro Grab Bag est vraiment utile pour tous ceux qui possèdent une caméra GoPro. Ce petit sac contient plusieurs accessoires pratiques, comme des fixations et des supports, qui sont parfaits pour personnaliser l’utilisation de la caméra. Je m'en sert pour mettre sur mon casque moto personnelement. Les accessoires sont de bonne qualité et faciles à installer. Le sac lui-même est bien conçu et protège bien les équipements. C’est un excellent complément pour ceux qui veulent avoir tout sous la main et organiser leur matériel GoPro. Je recommande vivement !