MADE IN USA-Tremolo Stopper

This little and cheap tool is quality and full of functionality. I don’t use it to block my tremolo for dive only, but it work excellent for that. I use it to help with restringing my 7-string guitars. Works like a champ and at this price and ease of installation every guitar I own will have one.

So this works exactly as it is supposed to. I also offset it to one side (as seen in photo) due to my addition of the third/center spring. Upon arrival the EVH 5150 had an ever so slight backwards tilt. This allowed me to set the tension to my liking (still needed to coax the claw for perfect tuning on low E) and keeping the bridge perfectly level. In my opinion the guitar should have come with one of these. The only drawback is that there is a “clunk” when the Floyd returns to rest. This cannot be heard through the amp though. So whether that is a drawback or not is debatable.

I installed this on a MIM Strat with a GFS brass trem block and using 4 Fender vintage springs. Installation is fairly straightforward, and you WILL need to setup the trem unit and adjust intonation, and 'fiddle' with it until it is fine tuned. It took me about an hour to do all of this; your mileage may vary. Worked great, except: The guitar developed a horrible resonance when playing the "D" string in proximity to the 10th fret. Unusable. I'm sure that this is an isolated incident unique to this guitar. I plan to try this on another MIM strat in the near future. Will update . . .. ADDENDUM: Reinstalled this on an early '90's Jackson with a Floyd and it works GREAT! No funny noises, no buzzes. Can tune to drop D without retuning everything else. A worthwhile investment.

I installed this trem blocker on my Charvel San Dimas along with an EVH D Tuna. Installation was a breeze. Work carefully, move trem springs out of the way, mark your spots, drill pilot holes, tighten screws by hand, adjust trem block and go. Works like a charm. Noticeable improved sustain, other stings stay in tune during bends, and the DTuna goes from E standard to drop D perfectly. I will probably put one on each of my Floyd Rose equpped guitars. A+ product.

It works to stabilize the Tremolo but understand what it does. It will prevent pulling back (up) on the trem but you need to tighten it down a decent amount to allow clean in pitch double stop bends. If you think you can just then adjust the screw back out to allow floating without having to retune, you cant, it will be sharp. As you bend you increase the tension on the strings pulling the forward thus moving the block back and detuning the other strings unless you crank it in a bit. you will have to play with it to get it where you want it. it will hold the tuning if a string breaks and allows for drop tuning and is great for re-stringing, worth it for just that.

I found this easy to install and stabilizes my stratocaster tremolo allowing easier tuning and intonation. The Tremsetter is also a great product, but requires a lot more skill and is a pain to fine tune. I mount this in the middle and use 4 springs total. I can't raise pitch, but you can drop the pitch like any tremolo. If you tighten the springs enough you can bend 1 1/2 steps and do unison bends while in tune and also mute and hit chords hard w/o warble. Another option is just tightening all springs and decking the tremolo, but I feel this changes the angle on the saddles which I feel affects my tone. This product is great for stability overall, but if you dive enough, your strat will most likely get seriously out of tune, in my experience, 1 of my strings always gets stuck at the nut, and is sharp or flat. I need to buy a few more of these.

I absolutely love this product. It's very low profile when compared to similar items, easy to install, and it functions exceptionally well. I purchased a similar item a few years ago (same function/idea), but it didn't have a low profile, so I had to route about 3/16" of an inch out of the underside of my guitar to make it work. Not so with this one. Because of it's low profile (height) I was able to mount it to my guitar straight from the package with no other modifications needed. If I pick up any more guitars with floating bridges, I'll definitely be installing the Tremolo Stopper as the first order of business.

The tremolo stopper works exactly as designed, but it has a flaw. It creates more sustain at the point it touches the bridge. I installed it right around g/b strings. When you strum you can hear a distinct change in timbre and sustain in the strings where it is touching. It was very noticeable with clean tone If you play with tons of distortion you won't notice as much. I suspect you could use 2 of them to offset this.

Love this item, it's a hell of a lot cheaper than more recognised "named" products but does the job equally well. Suits me perfectly. Got it in a BC Rich guitar with Floyd rose trembling.

Great little trem stop, easy to install

Excellent piece of kit. Solid, small, easy to install, does the job and doesn't appear to drift. Tuning has been stable in the weeks since installation. Refreshingly inexpensive too.

This is a great way to save. It's far more economical than the tremol-no which runs from 60-100 bucks. This thing is a fraction of that price and works just the same. I recommend it

good