Tecmojo 12U Wall Mount Server Cabinet IT Network Rack Enclosure Lockable Door and Side Panels Black,Cooling Fan,Glass Door,17.7inch Depth,for 19” IT Equipment,A/V Devices

Installed this rack to hold Unifi UDM Pro, unifi switch, AT&T Fiber gateway, etc. and it’s great. Easy to install on the wall and holds everything together very good.

When purchasing a brand that you're not familiar with, it can instill a bit of purchase hesitation. That said, I will not hesitate to purchase TecMojo products in the future as I'm very pleased with my purchase and customer service.I purchased the 18U unit and got it yesterday. I put it together right away and immediately noticed the packing was really good. There were no damaged corners or other parts, despite the box showing signs of rough handling. Everything was wrapped and padded well and all parts were in perfect condition. For the price point, I wasn't expecting 1/4" steel or anything, but I was impressed by the build quality. It seems to be built well and parts are of good quality. It's nice that all three of the locks use the same key. You get two keys for each lock, so you'll have more than enough keys.Customer service is excellent. I had an issue with the fan not working out of the box and it was resolved in under 24 hours. Amazing!The instructions are not fantastic with a few key items not illustrated. Assembly took about 20 or 30 minutes but may go quicker for you if you finish reading this message before you start. The below notes and attached pictures will help you get it done quickly and right the first time.1) The hex screws are for the frame, screwing into the square holes with nuts already in place. The other 8 machine screws and nuts attach the vertical rails to the inside of the frame.2) There's a small black washer zip-tied to the door. This is very important and not mentioned on the assembly sheet. This goes on the bottom pin of the door. Without this in place, the door does not close well because there's no gap between the door and the frame. The black washer adds that much needed gap. It's easy to miss it, so look closely. See picture.3) It was nice that many of the nuts for the square holes were already in place right out of the box. If you see one or two holes without a nut, look inside the box and in the corner areas of the parts. There were three that got knocked out during shipping, but they were in the corner of the front frame.4) The lock on the door requires a part not shown on the assembly instructions. It's a silver part with a round hole and one edge that's bent at 90 degrees. This goes on the inside of the door between the door and the washer and nut for the lock. The flat side lays on the edge by the glass and the edge that's bent goes directly on the door. This gives you a flat surface to install the lock whereas without it, installing the lock wouldn't be possible. See picture5) The locks on the right and left side have lock bars that have a bend in them. Make sure to assemble them with the bend going away from the lock so the lock bar latches properly. Otherwise the lock bar will hit the frame and not lock. See picture.Overall, I'm very pleased with this purchase and I will seek out TecMojo products in the future.

I purchased this rack multiple times and I am not a person to write a review but I believe this product deserve a good review. I believe I installed 6 of these racks for my customers and no complaint so far, easy to install and very good quality material. If you need a wall mount rack for your stuff I highly recommend this one.

Bought this to house new network equipment that I'd bought over the holidays and make my network/server installation "official" after years of stuff laying all over my office.The rack was easy to put together, although after assembling I found that one of the corners actually got bent either at the factory or during shipment (there wasn't obvious damage to the box that I could determine). This was disappointing, but luckily it was on a back corner and whatever exposed metal there is could be covered up with a black marker or similar. I mounted it to the wall by first mounting attaching vertical 2x4s to the studs and then attaching the rack to them, so mounting was straightforward and allows the rack to ventilate from the back as opposed to be mounted directly to the wall. Is this a bullet-proof rack made of thick gauge steel? No, but it's not priced as one either. The smoked glass door is nice and increases the wife-approval rating of the rack :)I replaced the single, loud ventilation fan with dual USB-connected fans that are quite quiet, but the main reason why is because this is mounted in my work area. If this rack wasn't being installed in a quiet environment, the included fan seem to ventilate well.With a combination of standard rack mounting and shelves that I purchased for non-rackable equipment, the fit and function of the rack seems great and exactly what I needed.

Well designed and constructed. Nice mounting template made wall mounting easy and accurate.